 |
| Quantity: | |
|---|---|
JV-555
JERVAY
ALL ROUND WET RUBBING FASTNESS IMPROVER JV-555
polyester cotton reactive dye wet rubbing fastness improver
I. MAIN COMPONENTS
Special Waterborne Polyurethane
II. PRODUCT PROFILE
The wet rubbing fastness of active, vulcanized, direct and indigo dyes on cellulose fibers is especially low when they are thick and dark, especially the wet rubbing fastness of big black, big red, emerald green and so on is often lower than grade 1, while the wet rubbing fastness of textiles exported to Europe and America requires more than grade 3; the wet rubbing fastness can fully meet this requirement. This product improves the stability of salt and alkali on the basis of raw materials and reduces the shortage of the structure of the product itself.
III. TECHNICAL INDICATORS
Appearance: light yellow to yellow transparent liquid
Ionic: weak cation
PH value: 4.5 ± 1 (pure water)
Solubility: easily dispersed in any proportion of tap water
IV. MAIN PERFORMANCE
1. Without formaldehyde and APEO, it belongs to environmental protection products.
2. It is easy to use, and it can be used directly with water.
3. The handle of the fabric is soft, and has no effect on the color light and sunlight fastness.
4. It can greatly improve the wet rubbing fastness by 1-1.5 grades, reaching more than 3 grades.
V. APPLICATION METHODS
According to the type and concentration of dyes used and the types and forms of treated fabrics, the usage is as follows:
1. Impregnation method (limited to water treatment plant)
Dosage: 2-4% (o.w.f.)
Bath ratio: 1:10 ~ 20
Process: dyed fabric (pH ≤ 6.5) → dipping (room temperature, time: 20 ~ 30min) → drying
2. Dip rolling method: 30-50g / L; glacial acetic acid / citric acid: 0.5-1.0g/l
Process: dyed fabric (pH ≤ 6.5) → dip and roll (rolling yield: 80-85%) → drying
VI. POINTS FOR ATTENTION
1. The temperature of working fluid should be controlled between 25 ℃ and room temperature.
2. Before use, clean the cloth surface alkali (control pH ≤ 6.5), salt and soaping agent.
3. use a long time to produce a large amount of foam in the rolling tank. Remove foam or clean the groove and replace the working fluid before setting.
4. Try to keep the pH value of working fluid in the range of 4.5-5.5.
5. The water used for working fluid should be tap water ≤ 100ppm, and groundwater or river water should be treated and reused.
6. Please use it immediately after preparation, and do a good job of sample test before use. The above process is only for reference.
7. It can only be used alone and can not be used in the same bath with silicone oil, softener, fixing agent and anionic auxiliary agent.
VII. PACKAGING STORAGE
125kg / plastic barrel sealed at room temperature, shelf life of 6 months.
1. What’s your MOQ?
Our MOQ is 1kg. But usually we accept less quantity such as 100g on the condition that sample charge is 100% paid.
2.Is there a discount?
Discount according to the quantity and product!
3.Are manufacturer or trading company?
Yes we are manufacturer. You are welcome to visit our factory.
4.Which kind of payment terms do you accept?
For small order, you can pay by T/T or L/C
And For bulk order, you can pay to our company's bank account.
ALL ROUND WET RUBBING FASTNESS IMPROVER JV-555
polyester cotton reactive dye wet rubbing fastness improver
I. MAIN COMPONENTS
Special Waterborne Polyurethane
II. PRODUCT PROFILE
The wet rubbing fastness of active, vulcanized, direct and indigo dyes on cellulose fibers is especially low when they are thick and dark, especially the wet rubbing fastness of big black, big red, emerald green and so on is often lower than grade 1, while the wet rubbing fastness of textiles exported to Europe and America requires more than grade 3; the wet rubbing fastness can fully meet this requirement. This product improves the stability of salt and alkali on the basis of raw materials and reduces the shortage of the structure of the product itself.
III. TECHNICAL INDICATORS
Appearance: light yellow to yellow transparent liquid
Ionic: weak cation
PH value: 4.5 ± 1 (pure water)
Solubility: easily dispersed in any proportion of tap water
IV. MAIN PERFORMANCE
1. Without formaldehyde and APEO, it belongs to environmental protection products.
2. It is easy to use, and it can be used directly with water.
3. The handle of the fabric is soft, and has no effect on the color light and sunlight fastness.
4. It can greatly improve the wet rubbing fastness by 1-1.5 grades, reaching more than 3 grades.
V. APPLICATION METHODS
According to the type and concentration of dyes used and the types and forms of treated fabrics, the usage is as follows:
1. Impregnation method (limited to water treatment plant)
Dosage: 2-4% (o.w.f.)
Bath ratio: 1:10 ~ 20
Process: dyed fabric (pH ≤ 6.5) → dipping (room temperature, time: 20 ~ 30min) → drying
2. Dip rolling method: 30-50g / L; glacial acetic acid / citric acid: 0.5-1.0g/l
Process: dyed fabric (pH ≤ 6.5) → dip and roll (rolling yield: 80-85%) → drying
VI. POINTS FOR ATTENTION
1. The temperature of working fluid should be controlled between 25 ℃ and room temperature.
2. Before use, clean the cloth surface alkali (control pH ≤ 6.5), salt and soaping agent.
3. use a long time to produce a large amount of foam in the rolling tank. Remove foam or clean the groove and replace the working fluid before setting.
4. Try to keep the pH value of working fluid in the range of 4.5-5.5.
5. The water used for working fluid should be tap water ≤ 100ppm, and groundwater or river water should be treated and reused.
6. Please use it immediately after preparation, and do a good job of sample test before use. The above process is only for reference.
7. It can only be used alone and can not be used in the same bath with silicone oil, softener, fixing agent and anionic auxiliary agent.
VII. PACKAGING STORAGE
125kg / plastic barrel sealed at room temperature, shelf life of 6 months.
1. What’s your MOQ?
Our MOQ is 1kg. But usually we accept less quantity such as 100g on the condition that sample charge is 100% paid.
2.Is there a discount?
Discount according to the quantity and product!
3.Are manufacturer or trading company?
Yes we are manufacturer. You are welcome to visit our factory.
4.Which kind of payment terms do you accept?
For small order, you can pay by T/T or L/C
And For bulk order, you can pay to our company's bank account.
