banner_product
Products
You are here: Home / Products / Functional finishing agent / Three proofing finishing agent / Cationic C6 Water Repellent for Nylon And Polyester
Share to:

Cationic C6 Water Repellent for Nylon And Polyester

Model:C6303
Appearance:Milky emulsion 
Ionic :Slightly cation
pH:4 ± 2
Solubility    :Easily in water
Quantity:
  • C6303
  • JERVAY

WATERPROOF AGENT C6303

FLUORO CARBON BASED W/R, O/R & S/R AGENT (DURABLE TYPE ) ENVIRONMENT-FRIENDLY PRODUCT (PFOA / PFOS / APEO FREE)

NEOGUARD C6303 doesn't contain PFOA(Perfluorooctanoic acid) inducing endocrine disrupting chemicals. It doesn't have inflammability, volatility. It is a environment- friendly fluoro carbon base water/oil repellent.
NEOGUARD C6303 can be used for fabrics, non woven fabric, paper, and synthetic leather. NEOGUARD C6303 is specially effective to cellulosic fabrics, especially cotton, polyester, Rayon and their blends, Nylon, Acryl, P/C, P/NP, and Spandex by usage of small quantity.


<PHYSICAL PROPERTIES>

Appearance : Milky emulsion 

Effective component :Standard - 30% ± 1

Ionic nature : Slightly cation

pH : 4±2

Solubility : Easily in water


<CHARACTERISTIC>

1、C6303 is PFOA / PFOS / APEO free. 

2、C6303 is a environment-friendly product.

3、C6303 is suitable water repellent agent for cellulosic fabrics,especially cotton, polyester,

Rayon and their blends, Nylon, Acryl, P/C, P/NP, and Spandex by usage of small quantity.

4、C6303 has a good Internal bond strength with coating resin (PU, Acryl)

5、 C6303 has a good compatibility with other auxiliaries because of slightly cationic nature.

6、C6303 maintains stable emulsion by good physical stability to mechanical condition as high temperature, high pressure and high speed etc.

7、C6303 also has wide pH stable range but weak acid helpful for absorbance.

8、C6303 has not trouble caused by gum-up, separation, break of emulsion.

Rayon and their blends, Nylon, Acryl, P/C, P/NP, and Spandex by usage of small quantity. 


<TREATING METHOD>

1、C6303 can be diluted with water and treating process is


Padding
Spray                  --> Dry --> Cure 

Foam spread



* Adjust of bath(In the case of mixing with penetrating agent, resin and other finishing agent)


1) Put water in bath by 50% of total solution.
2) Agitate enough after put a other chemicals according to maker's recommendation.

3) Add C6303 to prepared bath and agitate slowly.
* Adjust of bath(In the case of mixing with penetrating agent, resin and other finishing agent)

4) Put water in bath by 50% of total solution.
5) Agitate enough after put a other chemicals according to maker's recommendation.6) Add C6303 to prepared bath and agitate slowly.


<APPLICATION>

Fabric

Padding

Tentering

Cotton

50-70 g/l

160°C X 120sec

Polyester

40-60 g/l

160°C X 60sec

Nylon

40-60 g/l

170°C X 60sec

Acryl

40-60 g/l

170°C X 60sec

P/C(=T/C)

40-60 g/l

160°C X 90sec

PNP

40-60 g/l

160°C X 90sec

P/U(Spandex)

40-60 g/l

150°C X 120sec

※ Prescription processing (for washing durability processing)
- C6303 (Water repellent) 100pt + WC-800 (Catalyst) 10pt


<PREPARATION FOR FINISHING>

1. Fabrics
1) Remove impurities by pre-treatment procedure. Alkali, spinning oil, sizing agent and other

surfactant are bad influenced to repellency.

2) After dyeing, remove completely a surfactant as levelling agent, dispersing agent and

penetrating agent, etc.
Reasonable pH condition is 5-6 and avoid from alkaline solution, it can be the factor of Gum-up and low water repellency.


2. Bath
1) Put water in bath by 50% of needed solution
2) Put resin, softener and etc according to the quantity consumed


Put reasonable amount of C6303 and check the bath condition (pH,stability If pH condition is exceed 7.0, add acid. Stability is problem, add IPA.


<OTHERS>

1. Avoid from mixing with anionic auxiliaries.
2. Fixing agent of reactive dyes can be influenced to water repellency.
3. Best repellency effect is needed proper repellent agent and catalyst.
4. Treatment with antipastic agent is needed careful consideration.
5. Remove floating matters in bath or some over-flow is better.
8. When bath color is changed by dyes come out from fabric, bath cleaning is needed.

9. Small size and auto-feeding bath is reasonable for W/R finish because it is effective to prevent ending or tailing.


<STORAGE AND HANDLING>

1. Store in -5°C ~ 40°C. Avoid from direct fire and light.
2. Close a cover fasten.
3. Low toxic but prohibit contact with the skin, eyes, inhalation and swallowing.


<OTHER INFORMATION>

Don't eat this product and further detail contents is in MSDS.


1. Do you provide FREE samples?

Yes,we could provide free sample,but the delivery cost will be on your side.

 

2. What’s the payment terms?

L/C or T/T will all be acceptable.

 

3. How’s the product delivery lead time?

Generally,ETD in 2 to 3 weeks if the product in stock. Others will be based on production schedule.

 

4. Do you provide customized product or new product developments?

Yes,we have research and development team to provide customized product developments.

Dyeing and finishing Auxiliaries

Industiral Cleaning Agent

Contact us

  No.16,huacuiyi lane,qiaotou town,dongguan city,guangdong province,China

QUICK LINKS

PRODUCTS

Contact person: Mr. Finn

Mobile No.: + 86 15014751722

  

Copyright © 2020 Dongguan Jervay Industrial Co. Ltd.      Support by leadong.